HASP SRM or not

Greetings,
I am attempting to emulate an aladdin hasp dongle and am having some issues finding out whether or not it is srm or not. I was unable to get a valid dump with HASPHL2010. I used toro monitor and was able to get passwords but h5dumper could not find the dongle, nor could h6... I was finally able to use RTDUMPERGUI to get a dump under the srm setting. I have uploaded the .txt file from haspmon3.2 and the srm dump file from RTDumper to the link below. From what I have found online there is not a public release for a srm emulator. Could someone confirm that this is indeed an srm dongle.
Cheers!
Link:
mediafire.
com/?7l12l43bz1z1a89,e4h9yaa66ygqqz1,bc31b4px97344po,f5dhdyhfk3fpjaz

is it possible to emulate srm?

Of course, emulate HASP SRM dongle is possible.

Seems your protected software using the dongle in HASP HL mode.
So, you can use any public emulator.

For HASP SRM private solution exists only.

Try make hasp dump files using h5dmp tool.
Run the tool under administrative rights with parameters:
h5dmp  0xACF 0x2949

Hi it seems the dongle is not srm but hasp hl.
I have got  a dump through h5dmp.exe and have a toro monitor log and a usb tracelog. I cannot get a working version of unidumptoreg downloaded. would someone give me some assistance as how to proceed?
Cheers!

here are the link to files I currently have:
h5dmp dump and .txt usb trace
mediafire.
com/folder/mbf1r92f9eux0/dongle

toro logs:
mediafire.
com/folder/bc31b4px97344po,e4h9yaa66ygqqz1/shared

Hi.
I have the same doubt. I do not know if my original dongle is a HASPL HL or a SRM key.
I read the dongle and according the following information it seems a HL key:


          ---===>Device Information<===---
English product name: "HASP HL 3.25"
ConnectionStatus:                 
Current Config Value:              0x01  -> Device Bus Speed: Low
Device Address:                    0x01
Open Pipes:                           0
*!*ERROR:  No open pipes!
          ===>Device Descriptor<===
bLength:                           0x12
bDescriptorType:                   0x01
bcdUSB:                          0x0200
bDeviceClass:                      0xFF  -> This is a Vendor Specific Device
bDeviceSubClass:                   0x00
bDeviceProtocol:                   0x00
bMaxPacketSize0:                   0x08 = ( 8 ) Bytes
idVendor:                        0x0529idProduct:                       0x0001
bcdDevice:                       0x0325
iManufacturer:                     0x01
     English (United States)  "AKS"
iProduct:                          0x02
     English (United States)  "HASP HL 3.25"
iSerialNumber:                     0x00
bNumConfigurations:                0x01
          ===>Configuration Descriptor<===
bLength:                           0x09
bDescriptorType:                   0x02
wTotalLength:                    0x0014
*!*ERROR: Invalid total configuration size 0x14, should be 0x12
bNumInterfaces:                    0x01
bConfigurationValue:               0x01
iConfiguration:                    0x00
bmAttributes:                      0x80  -> Bus Powered
MaxPower:                          0x19 =  50 mA
          ===>Interface Descriptor<===
bLength:                           0x09
bDescriptorType:                   0x04
bInterfaceNumber:                  0x00
bAlternateSetting:                 0x00
bNumEndpoints:                     0x00
bInterfaceClass:                   0xFF  -> Vendor Specific Device
bInterfaceSubClass:                0x00
*!*CAUTION:    This appears to be an invalid bInterfaceSubClass
bInterfaceProtocol:                0x00
iInterface:                        0x00
*!*ERROR:  0xFF is the prerelease USB Video Class ID
 
However, I tried to obtain the password using the HASP2010 (64 bits) and the password does not appears after open the software.
Any idea on the problem? Thanks in advance.

Open following link:
[You must be registered and logged in to see this link.]

Is any additional feature(s) exists, except '0' ?

Run the protected software and check active sessions for the features.

If any session exists it means that your dongle used in SRM mode.

Thanks for the support.
The result in the localhost is: [You must be registered and logged in to see this link.]

Your software uses SRM features.
So, private solution is possible only.

P.S. The expiration date can be removed or changed to 2099 year

Ok. Bad news...

The main objective was to emulate the dongle to run in several desktops (virtual machines).
Does the private solution creates a new physical key or a registry file?

Each year I have to updated the license and they present new releases of the software. Can the modification of the expiration date be done easily or is it also a private solution? Can the expiration date alteration be detected by the company?

Thanks.

I can answer on your questions only after the protection will be researched.

Do you need to have the dongle in your hands to research the protection?

Answered you in PM.

If u got dongle I help u for free.

ovis25 wrote:If u got dongle I help u for free.

Yes, I have the original dongle.

Hi guys, many thanks for the great job!
Can someone please help me? Sorry for my English 
I have a dongle HASP HL for a protected software that perhaps uses SRM features.
There is a solution for the emulation?

Hello,

Of course, the solution can be prepared.

What is name of the protected software?

Also needs SRM dump file from following tool:
[You must be registered and logged in to see this link.]

we can help  

Cheers.